5 min
60-series swivel hubs on a leaf front
Swivel housing kits for the solid front axle through August 1985, and why LN61 is not the same axle as LN60.
Summary: on a leaf-sprung solid front, the hub turns on a kingpin inside a swivel housing. Bearings, seals and shims live in that housing. Wobble, weeping oil, or a rough turn usually means this assembly — not a later independent-front arm bush.
Toyota Global 60-series launch covers YN60V and LN60V at launch with a rigid axle and leaf springs, then the August 1985 independent front. Match the axle in a photo before you order Autolink SH4 or All Four WBKHL2.
How to tell leaf front from independent front
- LN60, YN60 and RN60 through August 1985 carry leaves above a solid front beam (Autolink SH4).
- LN61 and YN63 from August 1985 use torsion bars and upper and lower arms; 48161-35110 is the front torsion bar on YN61, not a swivel kit.
- Stand at the front corner: one beam and leaves mean swivel hubs; two control arms and a torsion bar mean IFS bearings instead.
- Check your axle before ordering: LN61 and YN63 wagons from August 1985 use torsion bars (48161-35110), not a leaf-front swivel housing.
Sourced Toyota and aftermarket numbers
Part: Swivel housing kit
Number: Autolink SH4
What it fits: 4Runner LN60 and YN60 leaf front (Autolink SH4); LN61 and YN63 from August 1985 are IFS — not this swivel kit.
Part: Swivel hub kit
Number: Allied SH4E
What it fits: LN60R and YN60R leaf front (Allied SH4E); LN61R and YN63R from November 1985 only with a solid-front photo.
Part: Leaf spring eye bushes
Number: Whiteline kit
What it fits: LN60, LN61, YN60 and YN63 leaf eyes (Whiteline kit) — not the swivel housing.
Part: Torsion bar
Number: 48161-35110
What it fits: YN61G and YN61V August 1985 through March 1989 (48161-35110) — independent front, not a swivel kit.
Part: IFS wheel bearing kit
Number: All Four WBKHL2
What it fits: LN61, YN63 and 130 frames from August 1985 (All Four WBKHL2) — IFS wheel bearings, not swivel housings.
| Part | Number | What it fits |
|---|---|---|
| Swivel housing kit | Autolink SH4 | 4Runner LN60 and YN60 leaf front (Autolink SH4); LN61 and YN63 from August 1985 are IFS — not this swivel kit. |
| Swivel hub kit | Allied SH4E | LN60R and YN60R leaf front (Allied SH4E); LN61R and YN63R from November 1985 only with a solid-front photo. |
| Leaf spring eye bushes | Whiteline kit | LN60, LN61, YN60 and YN63 leaf eyes (Whiteline kit) — not the swivel housing. |
| Torsion bar | 48161-35110 | YN61G and YN61V August 1985 through March 1989 (48161-35110) — independent front, not a swivel kit. |
| IFS wheel bearing kit | All Four WBKHL2 | LN61, YN63 and 130 frames from August 1985 (All Four WBKHL2) — IFS wheel bearings, not swivel housings. |
Symptoms on a solid front
- Steering wander on the highway before you chase the steering box — kingpin and bearing wear in the swivel.
- Grease thrown onto the inside of the wheel from a failed seal.
- Clunk over bumps at the front that is not a shackle — beam wagons wear swivels and leaf eyes separately.
- Heat at the hub after a short drive — binding bearing or dry kingpin — stop and check before a long trip.
Swivel job versus leaf-eye bushes
Whiteline leaf spring eye bushes quiet clunks at the spring eyes on LN60, LN61, YN60 and YN63 — see 60 leaf spring bushes. That job does not replace bearings inside the swivel housing. Photograph where the noise originates before you order both kits.
Manual hubs and transfer lever on early 60
Many 60-series Surfs use manual front hubs and a floor transfer lever — hubs and 4WD. Swivel wear is unrelated to hub dial service. Transfer gear oil is its own fill on transfer case oil.
Narrow diesel timing on the same platform
LN60 and LN61 2L diesel use a narrow cam belt on Precision International 94050 — see 60 diesel timing narrow belt. That engine work does not fix a wobbling hub, but a buyer inspecting a 60 should ask belt width as well as swivel play.
Rear leaf eyes at the same time
A solid-front 60 still carries leaf springs at the rear (Toyota Global 60-series launch). Clunks from the back may be Whiteline leaf spring eye bushes on LN60 and YN60 while the front wanders from Autolink SH4 wear — photograph both ends before you quote one kit.
Ordering swivel parts from a photo-less ad
Marketplace ads that say LN60–LN61 without a beam photo are not enough for Allied SH4E versus All Four WBKHL2. Ask for a front-corner image with leaves visible (Toyota Global 60-series launch) before you pay freight on the wrong generation.
What does not fit
- RoughTrax lower front wishbone for a 130 arm on a solid-front wagon.
- 185 front coil spring on PartsNext 48131-35130 — third-generation part.
- 185 vacuum ADD actuator on 41400-35020 when the wagon has manual hub dials on a 60.
- 130 ID Workz SuperPro upper arm bush on a solid beam.
What to photograph before you order
- Build plate with LN, YN or RN letters and build month (Toyota Global 60-series launch).
- Front corner showing one beam with leaves or two arms with a torsion bar.
- Hub grease pattern on the inside of the wheel.
- Kingpin area with the wheel removed if the seller allows — in a workshop if not on the roadside.
Workshop hand-off notes
Give your workshop the model code photo and whether the wagon is solid front or IFS before they quote Autolink SH4. An alignment check after swivel or bearing work is sensible on All Four WBKHL2 IFS wagons — caster and camber settings for LN61 and YN63 are unconfirmed here; check your workshop manual.
Frequently asked questions
- Most LN61 wagons are IFS after August 1985 (Toyota Global 60-series launch) — photograph the axle before you order Autolink SH4 swivel hardware.
- Allied SH4E heading with LN61? Read the solid-front qualifier — not proof for IFS on All Four WBKHL2.
- Same as 130 ADD? No — 130 is a later generation with vacuum ADD on 41400-35010.
- Torque specs for kingpin nuts? Unconfirmed here — check your workshop manual.
- Where next for 60 front? 60 axle solid versus IFS for the generation map.
After Autolink SH4 or Allied SH4E work, retorque wheel nuts after the first short drive — kingpin and bearing jobs change hub standoff. Grease the kingpin on the schedule in your workshop manual; unconfirmed intervals here. Keep the old seal part numbers in your phone gallery beside the Toyota Global 60-series launch plate photo for the next owner.
Have the plate handy?
Add the model code on the fitment summary form. A part that is not in the tree can still be described there.
Fitment summary form