Australia and New Zealand · 60 · 130 · 185

YotaSurf60 · 130 · 185 reference

7 min

130 front suspension: torsion bar, arms, and bushes

Torsion-bar front, upper and lower arms, and bush kits for the second-generation Surf — and the 185 coil front and 60-series arms that do not belong on it.

Summary: the second-generation wagon keeps a torsion bar and control arms at the front, and coils at the rear (Toyota Global 130-series launch). The next wagon replaced those torsion bars with front coil springs (Toyota Global 185-series launch). A clunk over a driveway lip is often a bush or a ball joint on this front, not a rear shock and not an 185 coil.

Arm bushes, a lower arm, and a torsion bar are three orders. Rear coils, a panhard rod and TEMS dampers live on the 130 rear shocks guide. How to tell this nose from the next shape is on 130 versus 185 in the driveway. Lift height in millimetres is unconfirmed here. Measure the wagon you have. Ball-joint torque is unconfirmed. Check your workshop manual.

Suggested filename: guide-130-torsion-bar-front-corner.jpg. Wheel on, bar and both arms in frame, no jack hiding the spring.

What you should see under the front

Bush, ball joint, or bar

A dull knock at walking pace, gone when you load the suspension in a car park, is often an inner bush. A knock that follows the steering wheel, or a wander on the highway, can be a ball joint or a tired outer pivot. A nose that sits low on one side, with no knock, is more often the torsion bar or its anchor than a polyurethane bush kit. Photograph the corner that makes the noise before you buy a full set for both sides.

Polyurethane bushes change the feel. They are a choice for a tired rubber bush, not a lift kit and not a licence to crank the torsion bars until the upper arm sits on the bump stop. Ride height after a bush swap is unconfirmed here. Check your workshop manual for the adjustment, and have the wheel alignment done after the arms are tight. Alignment specs are unconfirmed on this page.

Grease type for a greaseable bush is unconfirmed here. Check your workshop manual. If the workshop manual is gone, match the grease the bush maker packed with that kit and keep it off the brake disc. This page does not copy fluid tables. Engine oil and coolant for the same wagon are on the 130-series filters and fluids reference when the service is filters, not arms.

Numbers for this front

Part: Upper arm bush kit

Number: SuperPro upper

What it fits: 4 Runner LN130, RN130, KVN130, VZN130 and YN130, 1988–1996 (ID Workz SuperPro upper arm bush).

Part: Lower arm

Number: SH05106

What it fits: Right-hand lower arm for Surf LN130 2LT turbo diesel and KZN130 1KZ-TE, with OE numbers including 48068-35090 (RoughTrax lower wishbone).

Part: Front diagram

Number: 130 front

What it fits: Front arm and torsion-bar hardware for this generation (JP-CarParts 130 front suspension).

Part: Rear diagram

Number: 130 rear

What it fits: Rear coil and shock hardware, not the front arms (JP-CarParts 130 rear suspension).

Arms that belong on a different wagon

Part: 60-series upper bush

Number: Whiteline upper

What it fits: Hilux 4 Runner LN61 and YN63, not a 130 arm (Parts360 Whiteline upper bush).

Part: 60-series lower bush

Number: Whiteline lower

What it fits: LN61 and YN63 independent front, November 1985 through September 1989 (Parts360 Whiteline lower bush).

Part: 185 front coil

Number: 48131-35130

What it fits: Front coil for Japan Hilux Surf KZN185 SSR-G, SSR-X and SSR-V (PartsNext front coil). Not a torsion bar.

Part: 185 arm bushes

Number: N180-185

What it fits: Control-arm bushes aimed at the coil-front wagon (Whiteline 185 control-arm bushes).

Part: Leaf-eye kit

Number: Leaf eyes

What it fits: 4Runner LN60, LN61, YN60 and YN63 leaf eyes (Car Toys leaf-eye kit). Not a 130 control-arm bush.

Part: 60 torsion bar

Number: 48161-35110

What it fits: Right-hand torsion bar for Japan HILUX YN61G and YN61V August 1985 through March 1989 (PartsNext 60 torsion bar). A different front from this wagon.

Left and right are not a guess

The lower-arm line used here is a right-hand arm for LN130 and KZN130 (RoughTrax lower wishbone). Order the side that is damaged. A "pair" title that never says left or right is how people freight the same arm twice. Ball joints pressed into the arm may or may not come with a bare arm. That split is unconfirmed on this page. Photograph the joint and ask before you pay.

VZN130 is the 3.0 petrol on this shell and YN130 carries the 3Y, with the same front layout and different service parts from the diesels (Toyota Global 130-series launch). Its front arms are this generation's arms. Keep the petrol guide for this shell for the engine, and this page for the torsion bar.

Rear shocks are not this job

Electronic damping on some of these wagons is a rear-absorber question. A front bush kit will not fix a TEMS warning or a rear lean. Use the 130 rear shocks guide when the top mount or the lateral rod is the photo you actually need. A 185 rear coil is a later wagon again (JP-CarParts 185 rear suspension).

Early 60-series wagons that still have leaves, and the independent-front 4Runners that followed them, are the 60-series axle guide. Their bushes will bolt into a conversation at a counter and then not bolt onto this arm. If the plate is missing, the torsion bar behind the front wheel is the tell. A coil in the front guard means you are on the wrong guide.

On the hoist

Support the arm before you undo a ball joint. A torsion bar stores load. Letting it unwind without a jack under the arm is how people get hurt and how bolts bend. The unwind procedure and the torque that follows are unconfirmed here. Check your workshop manual. Mark the torsion-bar anchor before you move it so you can return the nose to the height you started with.

Press bushes square. A cocked bush wears the new arm eye and comes back as the same clunk. If the eye is oval, a bush kit is the wrong spend — the arm itself is tired. That is when the lower-arm listing matters, and only for the letters it actually covers.

After the alignment, drive a known bumpy street and a highway. A knock that remains on one side is often the side you did not replace, or a sway-bar link you did not look at. Sway-bar link numbers for this front are unconfirmed here. Check your workshop manual or photograph the link before you order.

What to photograph

  • Build plate with LN130, KZN130, VZN130 or YN130 (Toyota Global 130-series launch).
  • One front corner with the torsion bar and both arms, wheel on.
  • The torn bush or the ball-joint boot, close enough to see which pivot.
  • Both sides of the nose from further back, so a lean is obvious.
  • The rear spring, only so you do not order it by mistake while you are under the wagon.
Suggested filename: guide-130-upper-arm-bush.jpg. Bush eye fills the frame. Include a finger or a spanner for scale.

Frequently asked questions

  • Will an 185 front coil replace my torsion bar? No. Front coils on that number are for KZN185 SSR grades (PartsNext front coil), and the later wagon dropped the torsion bar (Toyota Global 185-series launch).
  • Do LN61 Whiteline bushes fit this arm (Parts360 Whiteline lower bush)? Those lines are the independent-front wagons from the previous shape, not this torsion-bar arm.
  • Is the lower arm the same left and right? The arm line cited here is right-hand for LN130 and KZN130 (RoughTrax lower wishbone). Confirm the other side before you buy two.
  • Can I wind the torsion bars up for a lift and skip the bushes? You can hide a sag and then destroy the ball joints. Height change in millimetres is unconfirmed here. Replace the knocked bush first, then align.
  • What torque on the ball joint? Unconfirmed here. Check your workshop manual.
  • Where are oil and coolant? On the 130-series filters and fluids reference, when that is the job. They do not choose an arm bush.

Have the plate handy?

Add the model code on the fitment summary form. A part that is not in the tree can still be described there.

Fitment summary form